Shop

Showing 73–92 of 92 results

  • Sintered Ptex Base Bright GREEN 1.2/330mm

    16.50 "incl. VAT"
    Add to cart

    Sintered Ptex Base Bright GREEN 1.2/330mm

    ski and snowboard ptex base uhmw pe material.

    IS 7200 628 Green 2G2GV 1,20/320

    Note: This base is older then 2 years, so you might need to flame it in order for the epoxy to stick to it well. See link below for instructions,

    https://www.junksupply.com/flaming-and-sanding-sidewalls-or-the-tip-filler-ptex/

    It is a Bright version of Green that matches the bright green sidewalls.

    sanded and flamed both sides

    IS 7200 Isosport, sintered quality base. Base for ski and snowboard.

    Color: P 802 C

    Width is 320mm and thickness is 1.2mm

    1m price, for orders of more then 1m, a single piece is supplied

    16.50 "incl. VAT"
  • PBT Polyester White topsheet material for watersport (ws100)

    13.00 "incl. VAT"
    Select options

    PBT Polyester White topsheet material for watersport (ws100)

    Coextruded PBT polyester white topsheet for kiteboards. Non impact modified,  designed specifically for watersports, kitebaords and wakeboards. High quality topsheet for graphics sublimation/heat transfer.

    0.5mm thick , 490mm wide.

    This is not impact modified so if you use it for skis/snowboard, it will chip more easy.

    This topsheet is fleece backed for improved bound to epoxy. A fluid epoxy will penetrate the fleece and bind well.

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    Graphics can be done with sublimation on the outside.

    SKU: N/A Category:
    13.00 "incl. VAT"
  • Polar Bear Heated compression epoxy

    49.0095.00 "incl. VAT"
    Select options

    Polar Bear Heated compression epoxy

    Epoxy resin for skis and snowboard.
    New mix ratio!

    Before using, read instruction below!!!

    1L Epoxy and 0.3L Hardener (This is a new hardener that mixes 100:30g)

    Pot life 25min @ 25C.

    The compression molding Polar Bear Biobased Epoxy System is designed for heat curing applications. Skis and snowboard manufacturing (also kite/wakeboards).

    Polar bear is a heated compression bio based epoxy.

    • Applications: Polar Bear Recyclable Epoxy System is specifically formulated for compression molding applications, such as for skis and snowboard manufacturing. Heat assisted curing.
    • Mix Ratio: 100:30 by weight

    Link to the TDS: TDS_POLARBEAR_R_ECYCLABLEHARDENER

    Make sure you use a digital scale. Mix by weight.

    Make sure you use gloves.

    SKU: N/A Category:
    49.0095.00 "incl. VAT"
  • 2.5mm ABS Filler Subtle ORANGE 310mm wide (pr.10cm)

    2.65 "incl. VAT"
    Add to cart

    2.5mm ABS Filler Subtle ORANGE 310mm wide (pr.10cm)

    price pr 10cm. Maximum length is 120cm

    Bright Orange ABS tip/tail fill.

    Modified thermoplastic Isosport ABS insert or filler material for tip or tail.

    310mm wide, 2.5mm thick.

    Sanded and flamed, ready for use.

    If more ordered then it is delivered in one piece!

    2.65 "incl. VAT"
  • 1.8/350mm UHMW Filler BLACK (pr. 10cm)

    2.80 "incl. VAT"
    Add to cart

    1.8/350mm UHMW Filler BLACK (pr. 10cm)

    Black UHMW tip filler for skis and snowboard.

    UHMW  insert or filler material for tip or tail.

    350mm wide, 1.8mm thick.

    Sanded and flamed, ready for use.

     If more then one piece is ordered then it is delivered in one piece!

    2.80 "incl. VAT"
  • Wakeboard / Kiteboard DIY Package kit

    159.00169.00 "incl. VAT"
    Select options

    Wakeboard / Kiteboard DIY Package kit

    Wakeboard / Kiteboard DIY Package kit to make your own kiteboard / wakeboard.

    Build a highest quality wakeboard/kiteboard your self.

    In the wakeboard / Kiteboard package you have all the materials needed to build a wakeboard or a Kiteboard

    • 1 Paulownia wood plank, perfect wood for core
    •  3m tri-axial 618g/22oz glass fabric 480mm wide
    • 14 x m6 inserts for salt water
    • 1.5m topsheet and 1.5m base of highest quality
    • 1,2L bio based epoxy resin.

    Sidewall material is optional. We recommend you add one 100% alcohol wipe pr. sidewall at leaset for cleaning and improved adhesion, read here.

    For tips and more info se below!

    SKU: N/A Category:
    159.00169.00 "incl. VAT"
  • Ski & snowboard edge bender Pro

    120.00 "incl. VAT"
    Add to cart

    Ski & snowboard edge bender Pro

    Ski and snowboard edge bending tool.

    Edge bender for mounting on a vice. By having it on a vice, you can adjust any radius you like.

    This edge bender can bend edges in 2 dimensions, for the base and for the tip/tail. See pictures on the bottom.

    Fits edges step 1.2-1.8mm

    suggested mounting distance between the 2 smaller wheels: 62mm (center).

    120.00 "incl. VAT"
  • Snowboard DIY package kit (Poplar/beech woodcore)

    205.00265.00 "incl. VAT"
    Select options

    Snowboard DIY package kit (Poplar/beech woodcore)

    Snowboard DIY standard package kit to make your own snowboard.

    All you need to build own snowboard!

    Read first how to work with the materials: https://www.junksupply.com/how-to-work-with-our-materials/

    • Poplar with beech stringers thru insert area, wood core.
    • 25oz triaxial glass fabric or carbon/flax mix for great performance and light weight.
    • 24pcs m6 inserts,
    • 1.2L epoxy,
    • 4m of 25mm VDS,
    • 2 sidewalls of your choice
    • tip/tail insert filler
    • 1.8m topsheet and base of your choice
    • 3.6m steel edges.

    We recommend you add one 100% alcohol wipe pr. sidewall at least, for cleaning and improved adhesion, read here.

    SKU: N/A Category:
    205.00265.00 "incl. VAT"
  • Sei Whale Universal All-purpose Epoxy FAST

    54.00105.00 "incl. VAT"
    Select options

    Sei Whale Universal All-purpose Epoxy FAST

    MIX RATIO UPDATED!
    Epoxy resin for skis and snowboard.
    Before using, read instruction below!!!

    Sei Whale is a clear, all-purpose, epoxy system with high UV resistance.
    Mix Ratio is 100:50g for Fast Hardener

    In general, dont mix more then 250-300mL in one container, the mix can become too hot and will harden fast.Low smell, low toxicity! Great to work with and more environmental!

    TDS_Sei_Whale_Epoxy_System

    Fast Cure: mix: 100:50g. (14-17 min pot life)
    Tack-free time for the fast version is below 5h and less than 8h for the slow one. In general always keep min. 24h in press for best result.

    In case of heat curing (if possible use the CPM or Polar Bear version for compression heat curing), in general at 50C it will cure in 3h, at 60C it will cure in 80 minutes. I personally never went over 60C, for 80C pressing I used CPM/305 or polar bear resin.
    Make sure you use a digital scale. Mix by weight.

    Make sure you use gloves.

    SKU: N/A Category:
    54.00105.00 "incl. VAT"
  • Splitboard wood core Paulownia/Poplar

    36.0041.00 "incl. VAT"
    Select options

    Splitboard wood core Paulownia/Poplar

    Splitboard snowboard wood core

    A lite and durable wood core made of Paulownia and Poplar mix, vertically laminated interchanging strips of 25mm. 10mm abs strip in the middle.

    For simulation use: 400kg/m3 densnity and 6800N/mm Y modulus.

    This is how we suggest to do insert area on these cores to avoid any pulling out of inserts, read here.

    Choose between several dimensions.

    SKU: N/A Category:
    36.0041.00 "incl. VAT"
  • IS 7200 1.2/330mm Sintered base BEIGE

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/330mm Sintered base BEIGE

    Sintered base / ptex UHMW PW for skis and snowboard.

    Please flame this base before use, or do a adhesion test first, as it might have weakened over time.

    7200 2G2GV W 812 1,2/330 BEIGE

    Color P 7540 C

    Tough sintered base for ski and snowboard. IS 7200.

    It is 1.2mm thick, this should fit with 1.2mm edges with no problem.

    1m price, for orders of more then 1m, a single piece is supplied

    Se below for more tips and info!

    16.25 "incl. VAT"
  • Sintered Clear ptex base 1.0mm

    15.75 "incl. VAT"
    Add to cart

    Sintered Clear ptex base 1.0mm

    Can be used with 0.9mm step edges!

    Tough sintered Clear base, highest quality base for ski and snowboard.

    Ptex 2001 Sintered

    Suitable for sublimation. Clear.

    It is 1.0mm thick, this should fit with 0.9mm edges with no problem.

    available width: 310mm.

    1m price, for orders of more then 1m, a single piece is supplied

    before cutting, lay the base on a flat table for about 48h the base will start to relax. The heating tunnel is just a fast way to bring out the tension.

    Storage: Room temperature with low temperature fluctuations. Humidity should not be too high. You can store it on the roll. If you recognize some warping you can also try to wind it in other direction for storage.

    15.75 "incl. VAT"
  • Union splitboard clips (full set)

    60.00 "incl. VAT"
    Add to cart

    Union splitboard clips (full set)

    Splitboard clips, full set.

    Integrated type, you need 3.1mm M5 inserts too.

    The Union Clips and Hooks are simple and easy to assemble.

    These clips are a full set and come with all needed screws and assembly.

    60.00 "incl. VAT"
  • Splitboard snowboard Poplar/Beech core

    36.00 "incl. VAT"
    Add to cart

    Splitboard snowboard Poplar/Beech core

    Splitboard snowboard Poplar/Beech core

    A wood core made of Poplar reinforced with 2 Beech wood stringers thru the board insert area, vertically laminated interchanging strips of 25mm. 10mm abs strip in the middle.

    For simulation use approx.: Density of 430N/mm and Y-modulus of 9300

    This is how we suggest to do insert area on these cores to avoid any pulling out of inserts, read here.

    Below you can find a detailed drawing of the core.

    Category:
    36.00 "incl. VAT"
  • Ski DIY Lite package kit (Paulownia or Bcomp core)

    295.00350.00 "incl. VAT"
    Select options

    Ski DIY Lite package kit (Paulownia or Bcomp core)

    Skis diy kit package to build your own skis.

    All you need to build own lite weight highest quality skis!

    Read first how to work with the materials: https://www.junksupply.com/how-to-work-with-our-materials/

    Item contains: 2 pcs Paulownia or Bcomp 200 (see wood category for more info), base + topsheet,  composite fabric of your choice, 1.2L  epoxy,  8m of 25mm VDS, 8m steel edges, 4 sidewalls + tip/tail fill.

    Fabric options:

    1. 25oz triax Glass fabric. Add UD stringers separately if you need extra pop.
    2. Biax carbon + UD Bcomp flax: 2m carbon biax 300gms fabric for top and bottom and 2m 300gms UD bcomp fabric for top and bottom. You get premium ultra-responsive performance ski that is damped with bcomp fabric. Best of both worlds..
    3. Biax Bcomp Flax + UD carbon: 2m Bcomp biax 350gms flax fabric for top and bottom and 2m 130gms UD carbon fabric for top and bottom. You get a responsive ski, with great characteristics between the carbon one and glass one. It is also very much environmentally friendly.

    We recommend you add one 100% alcohol wipe pr. sidewall, at least for cleaning and improved adhesion, read here.

    SKU: 10-1 Category:
    295.00350.00 "incl. VAT"
  • Snowboard DIY Bamboo package kit

    295.00360.00 "incl. VAT"
    Select options

    Snowboard DIY Bamboo package kit

    Snowboard DIY standard package kit to make your own snowboard.

    All you need to build own Bamboo snowboard!

    Read first how to work with the materials: https://www.junksupply.com/how-to-work-with-our-materials/

    • snowboard Bamboo , 1800 x 320 x 12mm
    • 25oz triaxial glass fabric or carbon/flax mix for great performance and light weight.
    • 24pcs m6 inserts,
    • 1.2L epoxy,
    • 4m of 25mm VDS,
    • 2 sidewalls of your choice
    • tip/tail insert filler
    • 1.8m topsheet and base of your choice
    • 3.6m steel edges.

    Due to the nature of bamboo, it does not have loads of torsional stiffness, so it benefits from carbon stringers diagonally or carbon biax. You can add this separately for top and bottom also if you like.

    We recommend you add one 100% alcohol wipe pr. sidewall at least, for cleaning and improved adhesion, read here.

    SKU: N/A Category:
    295.00360.00 "incl. VAT"
  • Ski DIY heavy package kit (Ash or Bamboo core)

    295.00410.00 "incl. VAT"
    Select options

    Ski DIY heavy package kit (Ash or Bamboo core)

    Skis diy kit package to build your own skis.

    All you need to build own skis!

    Wood core is a dense wood core of either Ash or Bamboo. Due to the nature of bamboo, it does not have loads of torsional stiffness, so it benefits from carbon stringers diagonally or carbon biax. You can add this seperatelly for top and bottom also if you like.

    Read first how to work with the materials: https://www.junksupply.com/how-to-work-with-our-materials/

    Item contains: 2 pcs Ash or Bamboo ski wood core, base + topsheet,  fabric, 1,2L  epoxy,  8m of 25mm VDS, 8m steel edges, 4 sidewalls + tip/tail fill

    Fabric options:

    1. 25oz Glass fabric. Add UD stringers separately if you need extra pop.
    2. Biax carbon + UD Bcomp flax: 2m carbon biax 300gms fabric for top and bottom and 2m 300gms UD bcomp fabric for top. You get premium ultra-responsive performance ski that is damped with bcomp fabric. Best of both worlds..
    3. Biax Bcomp Flax + UD carbon: 2m Bcomp biax 350gms flax fabric for top and bottom and 2m 130gms UD carbon fabric for top and bottom. You get a responsive ski, with great characteristics between the carbon one and glass one. It is also very much environmentally friendly.

    We recommend you add one 100% alcohol wipe pr. sidewall, at least for cleaning and improved adhesion, read here.

    SKU: 10-2 Category:
    295.00410.00 "incl. VAT"
  • Splitboard DIY Package Kit

    255.00435.00 "incl. VAT"
    Select options

    Splitboard DIY Package Kit

    A splitboard  diy package kit for making your own splitboard.

    Splitboard package kit. Includes all you need to build your own splitboard.

    • 1 splitboard wood core – poplar/paulownia or poplar/beech combo with 10mm abs in the middle.
    • 7,5m stainless steel edges 1.2mm
    • 1.75m triaxial glass fabric or carbon/flax mix for great performance and light weight
    • 1,2L epoxy resin
    • 2 ABS sidewalls
    • 7,5m VDS 25mm rubber
    • 1.75m ptex base
    • 1.75m topsheet
    • 1 x tip/tail filler insert material
    • 34 M6 inserts
    • optional splitboard clips

    We suggest you also add 6m UD carbon 50mm stringers for the 25oz triax glass version, so you can keep the core lite and thin, while still be able to get stiffness and improved performance.

    Slitboard clip inserts M5x1 height 3.1mm are also available in store.

    Tip: On how to implement and improve insert/binding area durability, please read here.

    We suggest you add 3-6m of 50mm carbon ud stringers in case you wish a reasonably thin ride with improved stiffness.

    Simulator example: splitboard simulate design example

    SKU: N/A Category:
    255.00435.00 "incl. VAT"
  • IS 4400 1.2/330mm Extruded base Cherry RED

    11.00 "incl. VAT"
    Add to cart

    IS 4400 1.2/330mm Extruded base Cherry RED

    Note: This base is older then 2 years, so you might need to flame it in order for the epoxy to stick to it well. See link below for instructions,

    https://www.junksupply.com/flaming-and-sanding-sidewalls-or-the-tip-filler-ptex/

    Isosport extruded 4400 quality base for ski and snowbaord.

    Cherry Red color, pantone PP 201 C

    1.2mm thick

    330mm wide

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    sanded and flamed on one both sides!  ( to give the best adhesion with epoxy)

    11.00 "incl. VAT"
  • UD Glass fabric 100mm / 300gms

    1.00 "incl. VAT"
    Add to cart

    UD Glass fabric 100mm / 300gms

    ON STOCK FROM 30TH NOVEMBER 2023.

    Uni-directional UD glass fabric. Perfect for adding extra stiffness to your skis or snowboard or kiteboard.

    100mm wide and  300g/m2

    Price is pr. 1m, if more is ordered it is delivered as one continuous piece.

    Category:
    1.00 "incl. VAT"

Showing 73–92 of 92 results