small

Showing 1–32 of 47 results

  • VDS rubber tape for skis and snowboard

    0.7584.00 "incl. VAT"
    Select options

    VDS rubber tape for skis and snowboard

    VDS rubber Tape for skis and snowboard

    VDS rubber is used in between the edges and the laminates, and possibly sidewalls and laminate in order to decouple these materials with very different characteristics and improve durabiliy and life of the products. It purpose is to make sure that the layers stay together even when flexing and under tension.

    We offer VDS Rubber ready to use in 13mm, 25mm or 300mm wide. Black or Whitish.

    Quality VDS from Austria.

    With 300mm wide VDS you can cover your full board or ski with VDS.

    0.7584.00 "incl. VAT"
  • Bcomp flax fabric (+/-45 Bi-axial)

    22.5044.00 "incl. VAT"
    Select options

    Bcomp flax fabric (+/-45 Bi-axial)

    Natural flax from Bcomp.

    This material is 100% natural and excellent for all products. The stiffness is higher then glass fabric, but lower then carbon. Please see datasheet and try simulator to get an idea.

    +/-45 degree layers in total 350g (175g each).

    select width 640mm or 1280mm.

    pr. 1m length. If more is ordered then it is rolled as one piece.

    Another great property is that the material works well as a dampener. This means you can use the Biaxial and UD flax together or you can combine them with glass or carbon.

    For sumulation use:

    Density: 1350

    Y modulus: 58500

    Please see datasheet for more: t-flachs-5008-e

    Instructions: The flax fiber absorbs more resin.

    Pneumatic presses with ~5  bar is recommended to make good laminate with minimum excess resin.

    Vacuum press: follow this resin quantity recommendations: resin / (resin + fabric) = 60%
    Spread the resin well with a roll on a flat surface or pour the epoxy on to the fabric and then make a roll out of it. Then let it soak for some minutes. Much easier than try to smear it out.

     Tip: Use masking tape when cutting it for better result!

    SKU: N/A Category:
    22.5044.00 "incl. VAT"
  • (PU) Urethane Resin Smooth Cast 65D (sidewalls, insert/fin, underfoot area)

    38.00 "incl. VAT"
    Add to cart

    (PU) Urethane Resin Smooth Cast 65D (sidewalls, insert/fin, underfoot area)

    Polyurethane PU resin for sidewalls for skis and snowboards.

    Smooth cast 65D, Polyurethane resin for pouring sidewalls, tip/tail filler, for insert area or fin area, underfoot reinforcement or even for topcoat or similar. Gives nice smooth finish. Easy to bind to epoxy after just machining.

    Easy to work with, super durable and easy to machine. Bounding with epoxy needs no treatment.

    Urethane resin can easily be poured in a channel and hardens quickly. It gives very durable and hard to break sidewalls, easy to machine and binds easily to other layers without flaming/sanding.

    38.00 "incl. VAT"
  • IS 7200/7500 1.8mm Sintered Base BLACK (skis and snowboard base)

    12.0029.00 "incl. VAT"
    Select options

    IS 7200/7500 1.8mm Sintered Base BLACK (skis and snowboard base)

    Sintered Base for skis and snowboard UHMW PE base ptex.

    1.8mm thick!

    Sintered thick quality base 100% recycled, similar to IS7200, for a most durable setup. Goes with 1.8mm step edges.  thickness is 1.8mm.

    For skis, that require minimum warping, use the 145mm wide base directly!

    price is pr. meter.

    Sanded and flamed on both sides.

    For more info, see below!

    12.0029.00 "incl. VAT"
  • ICP 8210 PA Polyamide/Nylon Topsheet CLEAR for Skis/Snowboard/Kiteboard (sublimation)

    14.5029.00 "incl. VAT"
    Select options

    ICP 8210 PA Polyamide/Nylon Topsheet CLEAR for Skis/Snowboard/Kiteboard (sublimation)

    PA Topsheet for skis, snowboard or kiteboard, wakeboard.

    PA nylon topsheet – ICP 8210 is a 2 layer topheet, PA11 and PA12. ICP 8210 is tough, durable topsheet. It is harder then TPU/ABS and higher quality. Highest quality topsheet on the market.

    Multiple sizes and surface finishes available.

    Protective film overview and spec is in the bottom of the page.

    Protective foil should not be removed until your product is complete!

    PA topsheet gives more stiff ride and is a bit harder to machine, so make sure you have sharp tools.

    It comes in flamed or sanded and flamed finish on epoxy side. Outer side can be glossy, matte or with a certain structure (or brushed).

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    14.5029.00 "incl. VAT"
  • ICP 8100 PA Polyamide/Nylon Topsheet (multiple sizes) WHITE (sublimation)

    21.5025.00 "incl. VAT"
    Select options

    ICP 8100 PA Polyamide/Nylon Topsheet (multiple sizes) WHITE (sublimation)

    Topsheet for skis, snowboard or kiteboard, wakeboard.

    ski topsheet, snowboard topsheet, kiteboard topsheet

    Isosport ICP 8100 PA / polyamide / Nylon topsheet in white. For sublimation. Finest colors and durability!

    PA nylon topsheet. Nylon is most tough and durable topsheet. It is harder then PBT topsheet and very scratch resistance, this is reflected in the price.

    Back is flamed and impregnated with fleece.

    PA topsheet gives more stiff ride and is a bit harder to machine, so make sure you have sharp tools.

    Outer side can be glossy, matte or with a certain structure (or brushed).

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    21.5025.00 "incl. VAT"
  • IS NHS R3428 1.2/300-330mm All-round Race base BLACK

    21.5023.50 "incl. VAT"
    Select options

    IS NHS R3428 1.2/300-330mm All-round Race base BLACK

    This is new series IS NHS R3428 race base from Isosport, highest quality all-round race (ptex) base.

    Sintered ski- and snowboard running surfaces made of UHMW polyethylene modified with special fluor and additives for better gliding at a wide range of conditions.

    Width is 330mm and thickness is 1.2mm.

    price is pr. meter.

    Sanded and flamed on both sides.

    before cutting, lay the base on a flat table for about 48h the base will start to relax. The heating tunnel is just a fast way to bring out the tension.

    Storage: Room temperature with low temperature fluctuations. Humidity should not be too high. You can store it on the roll. If you recognize some wraping you can also try to wind it in other direction for storage.

    SKU: N/A Category:
    21.5023.50 "incl. VAT"
  • IS CB 7115X Sintered BLACK base 350mm wide (100% RECYCLED)

    19.0023.00 "incl. VAT"
    Select options

    IS CB 7115X Sintered BLACK base 350mm wide (100% RECYCLED)

    Ptex, P-tex base or UHMW PE base for skis and snowboard.

    IS CB 7115X sintered base, in black.

    100% made of recycled ptex and therefor naturally friendly alternative to other bases!

    Top quality base in terms of gliding and durability. With added carbon.

    1m price, for orders of more then 1m, a single piece is supplied

    Gliding ability is in generally on top level.

    Sanded and flamed on both sides.

    For more info, see below!

    19.0023.00 "incl. VAT"
  • IS NHS GRAPHITE 1.2/330mm sintered base BLACK

    23.00 "incl. VAT"
    Read more

    IS NHS GRAPHITE 1.2/330mm sintered base BLACK

    IS NHS GRAPHITE sintered base, top quality base in terms of gliding and durability!

    1,20mm thick and 330mm wide

    1m price, for orders of more then 1m, a single piece is supplied

    high carbon content and depending on the base special carbon types included. This carbon types and quantity makes the base better to grind in process and less greying over time. Making this base very durable and very long lasting.

    Gliding ability is in generally on top level, similar to IS 7500 or better.

    Sanded and flamed on both sides.

    before cutting, lay the base on a flat table for about 48h the base will start to relax. The heating tunnel is just a fast way to bring out the tension.

    Storage: Room temperature with low temperature fluctuations. Humidity should not be too high. You can store it on the roll. If you recognize some wraping you can also try to wind it in other direction for storage.

     

    23.00 "incl. VAT"
  • Carbon fabric – Plain 160g (pr. 500mm length)

    20.00 "incl. VAT"
    Add to cart

    Carbon fabric – Plain 160g (pr. 500mm length)

    Plain carbon fabric. Carbon offers stiff construction and looks amazing. It is also great for reinforceing or gaining additional pop/spring.


    Thread pr cm2:
    4×4
    Plain weave
    Width: 100 cm

    Application:
    Reinforcement fabric for modelling, motor sports, marine construction, and sporting equipment

    If you order more then one piece, it will come in one single roll, uncut.

     

    Category:
    20.00 "incl. VAT"
  • IS 7200/7500 1.2mm Sintered Base ptex BLACK (skis and snowboard base)

    9.7519.00 "incl. VAT"
    Select options

    IS 7200/7500 1.2mm Sintered Base ptex BLACK (skis and snowboard base)

    Sintered Base ptex for skis and snowboard

    IS 7200-7500 Isosport, sintered quality base.

    Width is 125-350mm and thickness is 1.2mm.

    For skis, that require minimum warping, use the 140mm wide base.

    1m price, for orders of more then 1m, a single piece is supplied

    Sanded and flamed on both sides.

    For more info,  see below!

    9.7519.00 "incl. VAT"
  • Bcomp ‘AmpliTex Fusion’ Fabric – Unidirectional (multiple weight)

    3.2518.00 "incl. VAT"
    Select options

    Bcomp ‘AmpliTex Fusion’ Fabric – Unidirectional (multiple weight)

    Flax and carbon mix fabric, best of both worlds.

    ampliTex flax-carbon UD fabrics, non-crimp, in multiple widths and weights.

    170-225gms, 25-350mm wide.

    price is pr. 1m length. If more is ordered then it is rolled as one piece.

    Technical datasheet: t-flachs-5027-e

    Flax parameters: Density: 1350, Y modulus: 58500

    Carbon parameters: Density: 1700 Y modulus: 235000

    See guide on how to find averaged parameters for simulation

     

    SKU: N/A Categories: ,
    3.2518.00 "incl. VAT"
  • IS7200/IS7500 1.2mm Ptex Sintered Base CLEAR (skis and snowboard base)

    9.0016.75 "incl. VAT"
    Select options

    IS7200/IS7500 1.2mm Ptex Sintered Base CLEAR (skis and snowboard base)

    Clear sintered ptex base for skis and snowboard. Sintered Base for skis and snowboard UHMW PE base ptex.

    Tough sintered highest quality base for ski and snowboard.

    IS7500 from Isosport

    Suitable for sublimation. Clear.

    It is 1.2mm thick, this should fit with 1.2mm edges with no problem.

    available width: 145mm – 350mm.

    1m price, for orders of more then 1m, a single piece is supplied

    For more info, see below!

    9.0016.75 "incl. VAT"
  • IS7200 1.2/330mm Ptex Sintered Base Bright GREEN

    16.50 "incl. VAT"
    Add to cart

    IS7200 1.2/330mm Ptex Sintered Base Bright GREEN

    ski and snowboard ptex base uhmw pe material.

    IS 7200 628 Green 2G2GV 1,20/320

    Note: This base is older then 2 years, so you might need to flame it in order for the epoxy to stick to it well. See link below for instructions,

    https://www.junksupply.com/flaming-and-sanding-sidewalls-or-the-tip-filler-ptex/

    It is a Bright version of Green that matches the bright green sidewalls.

    sanded and flamed both sides

    IS 7200 Isosport, sintered quality base. Base for ski and snowboard.

    Color: P 802 C

    Width is 320mm and thickness is 1.2mm

    1m price, for orders of more then 1m, a single piece is supplied

    16.50 "incl. VAT"
  • IS 7200 1.2/330mm Sintered base BEIGE

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/330mm Sintered base BEIGE

    Sintered base / ptex UHMW PW for skis and snowboard.

    Please flame this base before use, or do a adhesion test first, as it might have weakened over time.

    7200 2G2GV W 812 1,2/330 BEIGE

    Color P 7540 C

    Tough sintered base for ski and snowboard. IS 7200.

    It is 1.2mm thick, this should fit with 1.2mm edges with no problem.

    1m price, for orders of more then 1m, a single piece is supplied

    Se below for more tips and info!

    16.25 "incl. VAT"
  • IS 7200 1.2/330mm Sintered Ptex base RED

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/330mm Sintered Ptex base RED

    Sintered Base for skis and snowboard UHMW PE base ptex.

    IS 7200 329 ROT 2G2GV 1,20/330

    Color Red, code P 179 C

    Sintered quality base 1.2 thick 330mm wide.

    Suitable for sublimation.

    sanded and flamed both sides

    1m price, for orders of more then 1m, a single piece is supplied

     

    16.25 "incl. VAT"
  • IS 7200 1.2/330mm Sintered Ptex Base BLUE

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/330mm Sintered Ptex Base BLUE

    Sintered Base for skis and snowboard UHMW PE base ptex.

    IS 7200 507 BLAU 2G2GV 1,20/330

    color blue, p 7461 c

    Suitable for sublimation.

    Width is 330mm and thickness is 1.2mm.

    1m price, for orders of more then 1m, a single piece is supplied

    Sanded and flamed on both sides.

    For more info se below!

    16.25 "incl. VAT"
  • IS 7200 1.2/330mm Sintered base GRAY

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/330mm Sintered base GRAY

    Sintered base / ptex for skis and snowboard.

    Please flame this base before use, or do a adhesion test first.

    IS 7200 703 GRAU 2G2GV 1,20/300

    Color P 7540 C

    Tough sintered base for ski and snowboard. IS 7200.

    Sanded and flamed both sides, however we do recommend to flame this material before layup if possible. For more tips and info read below!

    It is 1.2mm thick, this should fit with 1.2mm edges with no problem. 330mm wide.

    1m price, for orders of more then 1m, a single piece is supplied

    16.25 "incl. VAT"
  • IS7200 1.2/320mm Ptex Sintered Base GREEN (darker)

    16.25 "incl. VAT"
    Add to cart

    IS7200 1.2/320mm Ptex Sintered Base GREEN (darker)

    ski and snowboard ptex base uhmw pe material.

    IS 7200 621 GRÜN 2G2GV 1,20/320

    sanded and flamed both sides

    IS 7200 Isosport, sintered quality base. Base for ski and snowboard.

    Color: P 362 C

    Width is 320mm and thickness is 1.2mm

    1m price, for orders of more then 1m, a single piece is supplied

    16.25 "incl. VAT"
  • IS 7200 1.0/330 or 1.2/320mm Sintered Ptex base YELLOW

    15.0016.25 "incl. VAT"
    Select options

    IS 7200 1.0/330 or 1.2/320mm Sintered Ptex base YELLOW

    Sintered Base for skis and snowboard UHMW PE base ptex.

    IS 7200 115 GELB W 2G2GV 1,20/330

    Color Yellow, P 109 C

    Sintered quality base 1.0 or 1.2 thick 330mm wide.

    Suitable for sublimation.

    sanded and flamed both sides. Please check adhesion for this base first or reflame.

    1m price, for orders of more then 1m, a single piece is supplied

     

    15.0016.25 "incl. VAT"
  • IS 7200 1.2/320mm Sintered Ptex base PINK/PURPLE

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/320mm Sintered Ptex base PINK/PURPLE

    Sintered Base for skis and snowboard UHMW PE base ptex.

    IS 7200 305 PINK 2G2GV 1,20/320

    Color P 674 C

    Sanded and flamed on both sides. Please check adhesion for this base first or reflame.

    1m price, for orders of more then 1m, a single piece is supplied

     

    16.25 "incl. VAT"
  • IS 7200 1.2/330mm Ptex Sintered base WHITE

    16.25 "incl. VAT"
    Add to cart

    IS 7200 1.2/330mm Ptex Sintered base WHITE

    Sintered Base for skis and snowboard UHMW PE base ptex.

    Suitable for sublimation.

    This is some of the highest quality and toughest fast sintered ptex base, UHMW.

    IS 7200 isospeed WHITE.

    Width is 330mm and thickness is 1.2mm. Price pr.m.

    1m price, for orders of more then 1m, a single piece is supplied

    Base is sanded and flamed on both sides for best binding properties.

    16.25 "incl. VAT"
  • Ptex 2001 1.0/310mm Sintered Base CLEAR

    15.75 "incl. VAT"
    Add to cart

    Ptex 2001 1.0/310mm Sintered Base CLEAR

    Can be used with 0.9mm step edges!

    Tough sintered Clear base, highest quality base for ski and snowboard.

    Ptex 2001 Sintered

    Suitable for sublimation. Clear.

    It is 1.0mm thick, this should fit with 0.9mm edges with no problem.

    available width: 310mm.

    1m price, for orders of more then 1m, a single piece is supplied

    before cutting, lay the base on a flat table for about 48h the base will start to relax. The heating tunnel is just a fast way to bring out the tension.

    Storage: Room temperature with low temperature fluctuations. Humidity should not be too high. You can store it on the roll. If you recognize some warping you can also try to wind it in other direction for storage.

    15.75 "incl. VAT"
  • IS6000 0.9/480mm Crosslinked base CLEAR (sublimation)

    15.75 "incl. VAT"
    Add to cart

    IS6000 0.9/480mm Crosslinked base CLEAR (sublimation)

    Wakeboard and powsurf grind base / ptex base.

    Price is pr.1m. If more is ordered, single piece is delivered in 1 roll.

    IS 6000 base, also called wakeboard grind base, is a base very close to a sintered bases in quality terms.

    Ideal for wakeboard grind base or a lite weight ski or snowboard/splitboard or powsurf. 0.9mm step edges fit for this base.

    It is now thicker and more durable crosslinked base IS6000 with 0.9mm thickness and width of 480mm.

    Make sure you use outer side of the roll as epoxy side if both are sanded, or if one is sanded use that one!

    Se below Detailed description for more info!

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    15.75 "incl. VAT"
  • Bcomp flax fabric – Unidirectional (120gms, 700mm wide)

    15.00 "incl. VAT"
    Add to cart

    Bcomp flax fabric – Unidirectional (120gms, 700mm wide)

    Natural flax from Bcomp.

    120gms UD directional. 700mm wide.

    This material is 100% natural and excellent for all products. The stiffness is higher then glass fabric, but lower then carbon. Please see datasheet and try simulator to get an idea.

    For sumulation use:

    Density: 1350

    Y modulus: 58500

    Please see datasheet for more:

    http://www.bcomp.ch/media/amplitex_5033.pdf

    Another great property is that the material works well as a dampener. This means you can use the Biaxial and UD flax together or you can combine them with glass or carbon.

    pr. 1m length. If more is ordered then it is rolled as one piece.

    Note: This fabric will take  more epoxy then glass or carbon fabric.

    Instructions: The flax fiber absorbs more resin.

    Pneumatic presses with ~5  bar is recommended to make good laminate with minimum excess resin.

    Vacuum press: follow this resin quantity recommendations: resin / (resin + fabric) = 60%
    Spread the resin well with a roll on a flat surface or pour the epoxy on to the fabric and then make a roll out of it. Then let it soak for some minutes. Much easier than try to smear it out.

     

    Tip: Use masking tape when cutting it for better result!

    Category:
    15.00 "incl. VAT"
  • ICP 4160 coextruded PBT Polyester Topsheet WHITE (impact modified)(multiple sizes) (sublimation)

    12.0014.75 "incl. VAT"
    Select options

    ICP 4160 coextruded PBT Polyester Topsheet WHITE (impact modified)(multiple sizes) (sublimation)

    Coextruded impact modified, durable PBT (polyester) white topsheet for all categories. High quality topsheet for graphics sublimation/heat transfer.

    This topsheet is fleece backed for improved bound to epoxy. A fluid epoxy will penetrate the fleece and bind well.

    Graphics can be done with sublimation on the outside.

    Read more on sublimation here: https://www.junksupply.com/sublimation-heat-transfer-of-graphics-on-plastics/

    More durable and hard then TPU topsheet.

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    12.0014.75 "incl. VAT"
  • ICP 2115/2117 TPU/ABS Topsheet CLEAR (multipe sizes) (solvant ink.)

    9.0014.00 "incl. VAT"
    Select options

    ICP 2115/2117 TPU/ABS Topsheet CLEAR (multipe sizes) (solvant ink.)

    Topsheet for skis, snowboard or kiteboard, wakeboard.

    Isosport 2115, 2 layer, Clear TPU/ABS topsheet.

    Gives a bit softer ride and is less durable then PA topsheet, but still great durability.

    Epoxy Side: Inside of the roll, unless it has protective film, please check.

    Protective foil should not be removed until your product is complete!

    Corona treated on the epoxy side (this looks like a very smooth glossy side).

    PS: Please before using check if your topsheet has protective film on the outside. We try as often as we can to get topsheet with protective film but some batches do not have it. In this case you can tape the topside of your topsheet with clear application tape (ebay) or contact paper for protection of needed.

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

     

    9.0014.00 "incl. VAT"
  • IS6000 0.4/500mm Crosslinked base and topsheet CLEAR (sublimation)

    13.50 "incl. VAT"
    Add to cart

    IS6000 0.4/500mm Crosslinked base and topsheet CLEAR (sublimation)

    Clear Base for kiteboards and wakeboards.

    Topsheet for skis, snowboards, kiteboards and wakeboards.

    Price is pr.1m. If more is ordered, single piece is delivered in 1 roll.

    IS 6000 base from Isosport.

    Sanded and flamed on one side and structured on the other, no film.

    Durability wise it is between extruded and sintered bases. It is between PA and TPU/ABS topsheet.

    Graphics with Sublimation. If UV or Latex printing is only option, do tests with primer first.

    PS: Please before using check if your topsheet has protective film on the outside. We try as ofen as we can to get topsheet with protective film but some batches do not have it. In this case you can tape the topside of your topsheet with clear tape for protection of needed.

    13.50 "incl. VAT"
  • WS100 coextruded PBT Polyester topsheet (watersport version) WHITE 0.5/490mm (sublimation)

    13.00 "incl. VAT"
    Select options

    WS100 coextruded PBT Polyester topsheet (watersport version) WHITE 0.5/490mm (sublimation)

    Coextruded PBT white topsheet for kiteboards. Non impact modified,  designed specifically for watersports, kitebaords and wakeboards. High quality topsheet for graphics sublimation/heat transfer.

    0.5mm thick , 490mm wide.

    This is not impact modified so if you use it for skis/snowboard, it will chip more easy.

    This topsheet is fleece backed for improved bound to epoxy. A fluid epoxy will penetrate the fleece and bind well.

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    Graphics can be done with sublimation on the outside.

    13.00 "incl. VAT"
  • Bcomp flax fabric – Unidirectional (300gms, 350mm wide)

    12.50 "incl. VAT"
    Add to cart

    Bcomp flax fabric – Unidirectional (300gms, 350mm wide)

    Natural flax from Bcomp.

    UD directional 300gms, 350mm wide.

    Technical datasheet: t-flachs-5009-e

    This material is 100% natural and excellent for all products. The stiffness is higher then glass fabric, but lower then carbon. Please see datasheet and try simulator to get an idea.

    pr. 1m length. If more is ordered then it is rolled as one piece.

    For simulation use:

    Density: 1350

    Y modulus: 58500

    Please see datasheet for more:

    http://bcomp.ch/files/e_tds_ud_5009_5025.pdf

    Another great property is that the material works well as a dampener. This means you can use the Biaxial and UD flax together or you can combine them with glass or carbon.

    Note: This fabric will take  more epoxy then glass or carbon fabric.

    Instructions: The flax fiber absorbs more resin.

    Pneumatic presses with ~5  bar is recommended to make good laminate with minimum excess resin.

    Vacuum press: follow this resin quantity recommendations: resin / (resin + fabric) = 60%
    Spread the resin well with a roll on a flat surface or pour the epoxy on to the fabric and then make a roll out of it. Then let it soak for some minutes. Much easier than try to smear it out.

     

    Tip: Use masking tape when cutting it for better result!

     

    Category:
    12.50 "incl. VAT"
  • UD lightweight carbon fabric (130gms, multiple widths)

    2.5012.50 "incl. VAT"
    Select options

    UD lightweight carbon fabric (130gms, multiple widths)

    Uni directional – UD – 0 degrees carbon tape fabric.

    weight is 130gms. 50-300mm wide

    Carbon Heat Set Woven Unidirectionals are produced with unidirectional carbon fibres in the warp and very lightweight thermoplastic fibres in the weft. The thermoplastic fibres are fused to create a stable fabric that is very stable and easy to handle and cut. These fabrics are excellent for wet lay up and wet preg applications.

    pr. 1m length. If more is ordered then it is rolled as one piece.

    Fantastic fabric for improving your rides flex/stiffness, giving it extra pop or even making it more light weight.

    This fabric can be combined with our Bi-axial carbon fabric to get a triaxial performance fabric.

    Tip: Use glue to stick the carbon to the core before layup to make it stay where you desire.

    SKU: N/A Category:
    2.5012.50 "incl. VAT"
  • IS 4400 1.0/330mm Extruded base BLACK

    12.00 "incl. VAT"
    Add to cart

    IS 4400 1.0/330mm Extruded base BLACK

    Extruded Base for skis and snowboard HDPE base ptex.

    Can be used with 0.9mm step edges!

    Isosport 4400, highest quality extruded ptex base for ski and snowboard.

    Extruded base in Black color.

    1.0mm thick

    330mm wide

    Price is pr. 1 meter. If more is ordered, then it is rolled and sent as 1pcs.

    sanded and flamed both sides ( to give the best adhesion with epoxy).

    12.00 "incl. VAT"

Showing 1–32 of 47 results